How To Make 6X9 Car Speakers More Louder

If you are after some more vocals, then adding 6x9 car speakers into the rear parcel shelf of your vehicle is the best method for improving overall sound. 6X9 car speakers are great because they provide all level of sounds, they have a three way configuration. They can play bass, midrange and high end treble if your on an car audio budget. In the centre, there are several tweeters to play high frequency sounds and because the 6x9 car speaker cone has an large diameter, it can have potential to play decent bass too around 50 to 60 HZ. One 6x9 has the cone area to equivalent to an 8 inch compare parts subwoofer. JBL make loud and clear 6x9 car speakers, kicker is also an good option. If you are on an budget, boss audio and kenwood make ones that are entry level. To get the most out any pair of 6x9 car speakers, you will need to give them the power they are rated at. Each speaker will be rated at its own RMS ratting, ignore max or peak ratings on any speaker specification as these are unrealistic figures of its power handling.

For example, if your 6x9 car speaker is rated at 90 RMS, then you ideally you want to find an two channel car stereo amplifier than can provide the same amount of power or close to this number. You can wire your 6x9 performance car parts speakers to the rear channels on your car stereo, however the headunit won't have enough power to drive there to there full potential. This may cause your 6x9 car speakers to sound weak at high volumes and also to distort early. 

You can also add an separate graphic equaliser to boost the sound. This will provide you with the ability to have full control of the different frequencies that are going to the 6x9 car speakers. This allows you to increase and decrease bass and treble. Kenwood 5 band equaliser is very good from my experience, allows pure crips and clear highs, however this product is discontinued and no longer in product. You will be able to find an used car equaliser on ebay.

You can also place your 6x9 car speakers into individual speaker boxes that are readily available from ebay. The enclosure will allow your 6x9 car speakers to have more bass and punch. It will make the overall sound more stronger, if compared to them floating around in the parcel shelf in open space. Make sure you get 6x9 car speakers that are constructed from MDF to ensure you get an quality sound.

How To Improve The Sound Of an Car Speaker

If you want to improve the sound of your performance car parts audio speaker, increase the level of bass and treble, today you will find out how to do so. The first thing you need to consider upgrading the headunit. If your car is not so modern, you will be able to remove the current radio and upgrade it, either with an aftermarket double din or single din unit. Newer, cars that are made from 2015 onwards, tend to not have many headunit upgrade options, as the unit itself is built into the vehicle's dashboard. This is what makes having an old car fun, you can customise it without having any restrictions. Factory headunits don't really have much options when it comes to fine tuning sound. They don't have any equaliser options, they also have an poor internal amplifier which will distort at high volume levels. For this reason, I recommend Pioneer or Alpine as car audio brands to go for when purchasing an brand new headunit because they currently make the best headunits for the price you pay. Try stay away from android cheap china ebay car stereos as they provide poor and cheap sound quality.

Upgrading the speakers will also do wonders. Factory car speakers are made from cheap materials and are poorly constructed. They are designed to play an basic level of sound, you will notice that factory speakers don't produce alot of bass. This is because the material is paper which the cone is made out from and the  surround is made from cheap brittle rubber. If you want good sound that is loud and clear, upgrading the front factory door speakers to an component speaker setup is the best bet. This will contain an speaker and tweeter along with an crossover box to increase clarity and bass response. You can also upgrade the rear speakers if you wish to coaxial style speakers, these are easier to install as the tweeter is placed into the middle of the speaker. JBL make good car speakers if you are on an car audio budget, however if you have more money to spend on an car audio system, then JL audio is the brand for you.

Adding an car audio amplifier is also an great idea to improve the clarity of an compare parts audio speaker. However, installing an car audio amplifier can be an challenge task if you have not done it before. More power means louder volume and because an car amplifier is larger in size, it has more electrical components inside to produce an distortion free sound at higher volume levels. You will require new speaker wire to be ran down the car doors and you also need to purchase an correct car amp wiring kit as well. This will allow you to setup your car amplifier in your trunk and achieve amazing sound quality and clarity.

Sound deadening material is often overlooked, however it is very important. It will help get the most performance out of your car audio front door speakers. This is because it stops vibrations rattles that may occur when the bass drops from your music. This will provide an tighter more impactful sound that is loud and clear. It is easy to apply and usually sticks onto the surfaces. You can also apply it around the speakers and onto any holes or gaps you find within the door card. This will make the inner part of the door more sealed, to make it act as an mini speaker enclosure, to improve the frequency response of your car speaker.

How To Improve My Car Audio System To Sound Better

 

An factory car audio system is very basic, you will have cheap speakers and an standard radio. Unless, you paid extra to get the Bose or Harman Kardon system, chances are the sound quality and loudness will be poor. If this is the case, there are certain upgraded that you can do to improve the performance and clarity of your sound system.

Swap your factory cheap paper cone speakers for quality aftermarket ones. Factory speakers are made from cheap materials, paper being the most common. If your car is used, chances are the rubber surround on the factory speaker is degraded which can happen overtime, this is normal. Car audio people tend to spend the most money on upgrading the front speakers. This is followed by getting an component speaker upgrade with an dedicated tweeter and crossover network for sound separation. Usually in the back, coaxial speakers are fitted as they are more convenient to install as well. 

You also want to ask yourself, do you want more volume and less distortion? If so, then you have two choices you can go down the easy route and swap out the factory stereo or you can add an aftermarket stereo as well. If you are unable to upgrade the factory radio as its built in as part of the cars dashboard, you can purchase an RCA converter to provide RCA outputs to any factory amplifier of your choice.

Furthermore, you can also add sound deadening material and apply it onto the insides of your car doors and behind the car door card. This will allow you to stop vibrations and unwanted noises that may occur, it will also stop road noise too. This can increase the amount of bass response from any car door speakers that you fit because it seals up any gaps and sort of helps the inside of the door become like an small enclosure.

If you want to add more bass, then add an car subwoofer if you got space. A 12 inch car subwoofer in an sealed box is generally compact and works in most situations. It is loud enough and blends in nicely with your car door speakers. If you want something over powering, then any subwoofer fitted into an ported enclosure tuned to 35HZ on around 500 rms or more should shake your rear view mirror. Alpine make some nice subwoofers.

How To Make Car Speakers Very Loud Be Heard Miles Away

If you want your car audio system to play more clear and sound louder, then you have come to the right place. This car audio blog will help you learn more about the car audio journey. Factory car speakers are limited in terms of power handling and how much effort goes into research and design. This is because unless its an factory upgrade sound package that focuses on sound improvement such as bose or harman kardon, the standard car speakers will be made from poor materials. Paper is generally used for the cone and the rubber surround easily degrades overtime. 

If you want loud and more clarity, install an 6.5 inch car speaker component setup in the front doors and discard the back rear car speakers. This will provide better sound stage. Adding an separate two channel stereo car amplifier is also recommended. Match the rms of each speaker to an appropriate rms channel on an car amp brand of your choice. Use quality RCA cables to prevent buzzing noises being picked up by the speaker wire. Upgrading car speakers and adding an car amplifier is the best and two most important factors.

You can also upgrade the headunit, something more aftermarket will provide you with more sound adjustments. Some high end pioneer headunits have an built in equaliser which allows you full control of what frequencies your car speakers play. You can also get foam rings that go around the car speaker. What this does is trap the sound between the car speaker and door card so all the sound goes out of the grill. You can get these cheap from ebay. Also you can apply sound deadening material onto metal parts of the door frame, this allows less rattling to occur and chances of better bass response from the car speakers in the door 

How To Fix Pushed in Subwoofer Dustcap Kid Pressed it in

 

The centre of the car speaker is were the voice coil is located. This contains an small or large copper coil depending on the size of the car speaker. The purpose behind attaching an dust cap onto the middle part of any speaker or subwoofer is to prevent dust and dirt getting in. Dust particles can make there way into the car speaker mechanical parts and blow the voice coil. It is very easy for an voice coil to get misaligned, if this is the case, then this can cause poor speaker performance and strange noises to be heard such as rattling or scraping. Often kids when they see an car speaker, they gain pleasure from pushing in an car speaker dust cap, thinking they are in an arcade centre. Although this doesn't affect the performance of the car speaker, unless its actually torn and letting potential dust in, it can not be so pleasant to look at. 

There are many different ways to fix an car speaker that has been pushed in. The best effective method without damaging the car speaker is to use an hoover. Ensure you place the hoover on the lowest setting possible, so it doesn't damage the plastic or paper that it is made out from. Use the nozzle to suck out the car speaker dust cap, use you initiative to carry out the repair. You can also try using PVC insulation tape stick it directly onto the dented area of the dust cap. Once you have done this, slowly peel back the tape, the dust cap will depress itself.  

I hope this guide has helped you repair your broken car speaker. 

Why is one side of my car speakers not working? please help

Overtime, components in an vehicle degrade and will need replacing. This is common with the mechanical aspect of things such as working on the engine, but car audio also will need replacing at some point. From failed speakers to radios that no longer display anything on the screen, we have seen it all. If you have noticed that one side of your car speaker is working and the other car speaker on the opposite door is not, this troubleshooting guide will help you fix your problem. 

Working in the car audio industry and now an old hobbyist, let me explain an scenario to you. Each time you open and close an door, there is delicate wiring located within the rubber boot found between to vehicle chassis and the door. Over years of constant opening and closing, this will increase wear on the wires to an point that it will break them off. Before you start taking door panels off, pry off the rubber boot and inspect the speaker wires. Chance are the speaker wires have become brittle, to get your broken car speaker working again is simple. Find the broken wires, snip them off were they are broken from, obtain wire of an similar gauge and solder on the new wires. 

If its not the speaker wire found in the door, then check the car speaker itself. Remove the door card to expose the car speaker, you will find many videos on YouTube that can help you with this. Once you have done that, remove the car speaker. Inspect the condition, can you press down the cone? Is it rock hard, is the rubber surround damaged. These are all things you need to look at. Test the car speaker with an battery, does it make an noise? If the car speaker is not working, replacing it with an exact same one would be recommended. Possibly from an breaking car if its an factory speaker. Or if you fancy an upgrade get online and get yourself an set of brand new car speakers.

VIN Lookup is important to consider if purchasing an new car, this is because its essential to know your research when buying an vehicle. Previous damages that you may not been aware about can show up with an simple VIN check.

How To Make Car Speakers Louder / Learn From The Experts

 

If you want to make your car speakers louder, there are many ways to do this. You don't always have to spend loads of money to get the sound you want. The first most important factor that makes an big difference on how loud your car speakers are is the headunit. Factory radios provide something like 10 to 15 watts rms per each speaker channel. This is fine if you're using cheap stock paper speakers, but if you have upgraded your speakers to component or coaxial speakers, then you need an better headunit to give them the power they need. Aftermarket headunits from pioneer or alpine provided like 30 RMS output even though there claims on the front panel say 50 X 4. When purchasing in the car audio world, always when looking for amplifiers and speakers go with the RMS rating on the stuff. This is the true real wattage rating, anything that states max or peak is an waste, as its not real wattage ratings and only to sell the product to people that are new to car audio.

Adding an car amplifier is going to provide the best level of power to the car speakers. Make sure you add an additional four channel amplifier to power your four car speakers. Two speakers in the front and two speakers in the back. The RMS rating has to match what the voice coils the speakers are designed for. For example, an pair of 6x9 car speakers rated at 80 rms, need an car amplifier that provides 80 rms at 4 ohms. Class A/B amplifier are best to use or door speakers and not CLASS D, as it provides reduced distortion and better sound quality. 

Sound deadening material also can increase the loudness of your car speakers. This is foil like stick on stuff that is really thick and dense that is stuck onto the metal parts of the door. This sits just behind the removable door card that exposes the inner part of the door. The sound deadening material can also be used to seal up any gaps in the door, this allows to create an mini enclosure. This increases bass from the car speakers and overall makes the sound more stronger. 

Thicker speaker wire can be used and should be used when adding an aftermarket amplifier. 14 gauge speaker wire is good for car door speakers. 10 gauge for car subwoofers. Run the speaker wire down the inner panels of the car, when feeding it through the rubber boot, use an coat hanger to feed the wire through.

How To Fix Car Amplifier No Sound Coming Out of Car Speakers

A car amplifier is required to provide amplification to your car speakers or car subwoofer. This is to drive them to their full potential. If you’re getting no sound out of your car speakers, the first thing to check is the power light on your car amplifier. Is it powered on?? The light should be green. Red usually means something is wrong, as the car amplifier is gone into protect. This can happen for several reasons, I am going to go through them with you today. The first thing you need to understand is the car amplifier getting power? Get a multi meter and probe the 12 volt point on the car amp. It should be getting a reading of 13.7 volts or more. Probe the remote turn on terminal as well, the remote wire should receive anything from 5 volts to 12 volts when the key is switched to the ignition on position.

If you are getting a zero reading from the power wire, check the inline fuse found near the positive side of the car battery. Remove the fuse and inspect, the thin wire found inside the middle of the fuse should be not broken if the fuse is OK. If the small wire found inside the fuse is snapped, this will break the circuit allowing the car amplifier not to power on resulting in no sound. The best method is to troubleshoot the problem that caused this in the first place. Check all the connections and wires around the car amplifier area are securely tight and separated from each other. Once you have done this, also check the grounding location where the car amplifier sits. The car amplifier ground should be clean, meaning the paint around the mounting surface should be sanded away to bear metal. This will ensure the ground is optimal for sending proper voltage circulation to the amps internal power supply.

Also, make sure the RCA cables are connected firmly into the RCA 'INPUT' of the car amplifier and ensure that they are not mistakenly connected to the RCA 'OUTPUT' on a car amplifier. To verify if the RCA cables are faulty or not sending signal to the car amplifier resulting in no sound, get yourself a 3.5mm jack to RCA cables lead. Then plug the headphone jack looking plug into a device such as an mp3 player or smartphone and connect the other ends into the red and white RCA 'INPUTS' found on the car amp. Play a song from your portable device with the vehicle switched on, if the song plays then you fault with the RCA cable connection within the vehicle. The first thing to troubleshoot is to remove the headunit and inspect the RCA cable going either to the car of stereo or RCA line out converter.

How To Stop Car Speakers Making an Buzzing Sound when Driving

If you have recently added a car audio amplifier to your car audio system to your car door speakers and you notice you have interference, this can disrupt sound quality. At low volumes, you may hear a hissing or buzzing sound coming from your car speakers and it may gradually get louder as you increase the RPMS of the engine. This is a common car audio problem that many fail to resolve, today I am going to explain all of the different ways to help you get around this.

The first thing you should do to troubleshoot is to check the ground connection for the car amplifier. Moving it to another area that is the closest to the metal chassis of the car is always a better option. Finding a random screw is usually a poor ground. The best ground in all cars in the trunk area is under the carpet, the bolt that holds the seat belt down is the best location. Its solid to the cars metal and is strong metal, not tin metal welded onto the chassis of the car, which does work but it not pure metal. When creating a ground for your car amplifier, ensure that the ground where you mount the circle ring terminal is sanded down. From the factory, there is paint sprayed in this area and this can cause an poor electrical connection if not removed. Using sandpaper or a flat head screwdriver to remove any paint will expose the bear metal of the vehicle.

Finding a better ground location and preparing it correctly usually fixes this kind of problem. If the buzzing sound is still heard from your car speakers, then the next thing to do is replace your poor cheap RCA cables with expensive ones that have foil shielding. This prevents interference from being picked up, the cheap RCA cables you get free with most car audio car amplifier wiring kits don't have shielding in usually. You also want to run the RCA cables down your car on a separate side away from the power and blue remote wire. This is because the power cable or remote wire can leak out signals that can get picked up by the RCA cables. Moving the RCA cables further away from them two cables can prevent any kind of interference that may get picked up.

How To Wire 6X9 Car Speakers to Your Parcel Shelf

cheap ebay 6x9 car speakers

If you want more treble in your car, the most cost effective solution is to add an cheap set of 6x9 car speakers into your parcel shelf. 6X9 car speakers are often power hungry, so adding an two channel car amplifier to power them is usually an good idea to get full volume out of them. You can also connect them to the rear left and right channels from your factory stereo wiring harness, however you will also need to disconnect the existing rear speakers, before adding your 6x9 car speakers wires on. If you wire your 6x9 car speakers on top of the existing rear speakers already wired into your car, yes they will all play at once, but this will work is reverse affect as neither of the car speakers will get proper rated power to them. This can result in an unbalance sound that is waste time and money.

When finding an car amplifier for your 6x9 car speakers, make sure you find the RMS of each speaker driver and match the power handing. For example, if each 6x9 car speaker is rated at 100 watts rms, you want 100 watts or close rms produced by the car amplifier at 4 ohms to get the full potential out the speaker. I have seen many good 6x9 JBL car speakers gone into the bin by people that don't know how to setup of wire them correctly. Ignore MAX or PEAK power ratings, its just used to market products are nothing to do with the true output of the car speaker.

Installing an car amplifier is not complicated. You can purchase an car amp wiring kit from ebay or amazon that contains all the wires, 8 gauge wiring kit is recommend for 6x9 car speakers running from an usual two channel amp. The red power wire goes to the 12 volts positive terminal found on the car battery, inline with an fuse and fuse holder. The black wire goes to an grounding point, either an seat belt bolt or an factory ground. The blue wire goes to an ignition switched source in the fuse box, or to an dedicated remote amp turn on wire which is found on most aftermarket car stereos. The RCA cables basically feed signal into the amp from the radio. If you are using an factory car stereo, you will need an line output converter. Mount the car amplifier onto the back seat and wire up each 6x9 car speaker with correct polarity to the correct two channels. Once you have done that, setup the high pass filter to your listening tastes, for 6x9 car speakers I say 50 HZ is good. This is because 6x9 car speakers have the potential to act as mini car subwoofers, as they have enough cone area to make the equivalent to an 8 inch car subwoofer.

How To Add Car More Bass Into Your Car Without Subwoofer

cheap ebay 6x9 car speakers

Car subwoofers provide lots of bass, but at the same time they take a lot of space in the trunk. This means you may have to take it out when going to the supermarket or putting the kids push chair in. Thankfully, there are other ways to add more bass into your car without installing an proper large car subwoofer. Subwoofers come in 10, 12 and 15 inches and there is also the enclosure which houses it that takes even more space up. 6X9 car speakers can act like subwoofers if setup properly, they have large enough cone area to push enough air to create bass. 6x9 car speakers can be mounted into small MDF enclosures to increase the amount of bass. You can also mount 6x9 car speakers free air into the parcel shelf, when the trunk is closed it will act like an enclosure. 6X9 car speakers are easy to hide away and disconnect, making them an number one choice for adding more bass into your car. They also provide an increased sound in midrange and treble, as they have an variety of tweeters placed in the middle of them.

To get the most out of your 6x9 car speakers, ideally you would want to run an 2 channel car amplifier to send them the full RMS output that they rated to handle. This will ensure that your 6x9 car speakers have enough power to provide the full spectrum of bass. You won't get really low deep bass that sets car alarms off with 6x9 car speakers, but you will get enough bass that plays around the 50 to 60 HZ frequency range, which will make most music sound like it has bass. You will need to obtain an car amplifier wiring kit, make sure the gauge of the car amp wiring kit is the correct type for your amplifier. To be on the safe side, to get the maximum performance out of your car amplifier, 8 gauge ofc power and ground cabling should be used with an appropriate fuse holder if under 300 rms. Its important that you add an fuse holder to ensure if any short happens, your car circuit is protected.

An underseat subwoofer is also an good option, although it is called an subwoofer, its just an larger speaker in an metal enclosure placed under the seat. They provide more of an midbass punch 80 hz and above rather than low subwoofer bass, and they tend to cause more vibrations felt in the seat then bass being heard. However, 6X9 car speakers would still be my preferred method of getting more bass into your car, however if your not after pure sound quality and just want noise, then an underseat subwoofer is something you may consider An underseat subwoofer that I have reviewed is the kenwood KSC SW11. Its build quality is good, comes with its own adjustable bass remote and packs and punch. It is currently the best under seat car subwoofer that is out there right now.

How To Wire 6X9 Car Speakers To Car Radio

cheap 6x9 speakers

 

6X9 car speakers provide loudness and overall clarity in your car audio system. 6X9 car speakers are easily added to existing parcel shelf. Simply draw the inner outline of the car speaker and then cut around using your jigsaw. I personally think that JBL make the best sound 6x9 car speakers in the car audio market, they are loud with multiple tweeters and very bassy. You have two options to wire your 6x9 car speakers, the first being powering the speakers directly from the rear channels of your radio. This is the most easiest method, all you need to do is run two sets of speaker wire left and right down one of the car's plastic side panels to the back of the radio. When you do this, you will have to first disconnect the factory rear door speakers from the headunit wiring loom. You can't have the existing rear speakers playing in your car and add your 6x9 car speakers to the same channel. This will provide an unbalanced sound and the 6x9 car speakers will not get there full power. If your 6x9 car speakers have an RMS of around 30 to 40 watts, then running of an headunit is fine. An aftermarket radio will have more power than an factory radio. 

If you're running high powered 6x9 car speakers with big magnets, 80 to 100 rms each, then to get the most out of them, it would be recommended to get an external two channel amplifier. 2 channel amplifier will provide distortion free sound and will make your 6x9 car speakers really loud. Remember when purchasing an used or brand new car amplifier, that the rms rating at 4 ohms matches the rms rating on each speaker you want to power. Adding an car amp is more of an time consuming task. You will need to purchase an car amplifier wiring kit. This will contain all the bits you need to add an amp to your 6x9 car speakers. Stinger and vibe make good car audio wiring kits if your on an budget.

The red power wire will go to the 12 volt positive terminal found on the car battery, with an inline fuse to protect the vehicle. The black wire will be used for an ground, find an seat belt bolt to mount it to or similar look behind the rear trim carpets in the trunk and remember to remove any excess paint with an screwdriver. The blue thin wire is for the remote turn on, this needs to be attached to an ignition switched source in the fuse box.  This wire is used so the car subwoofer doesn't stay on all night and drain the car battery. The RCA cables plug directly into the output of the back of the aftermarket car stereo and into the input of the car amplifier powering your 6x9 car speakers. If you're using an factory car stereo, then plug the into the line out converter and tap into your rear speaker wires on the back of the radio. Setup the high pass filter to 100 HZ to filter out any bass so the 6x9 car speakers play loud and clear. Lowering the High pass filter number will increase the amount of bass, but can lead to unwanted distortion being heard at high volumes. Tune the gain to your liking, slowly increase and stop until you notice that the sound quality drops.

How To Wire 6X9 Car Speakers To Your Car Stereo

6X9 car speakers are an great addition to adding more volume to your car stereo, often they are fitted with an over powering subwoofer to increase the amount of treble in your car. This helps balance out the overall sound output from the vehicles car audio system, increasing the range of vocals, as when adding an aftermarket car subwoofer usually this creates overpowering bass to be heard without actually hearing the music. 6X9 speakers can be either fitted directly into the existing parcel shelf in your vehicle by cutting holes. In most cases this works fine, however if your have heavy duty 6X9 car speakers, then you may want to create an shelf out of MDF replicating the original parcel shelf but with stronger wood. Overtime, 6x9 car speakers that are loud with huge magnets can way down the parcel shelf and cause it to sink. 

In terms of wiring 6x9 car speakers there are an few options. One of the easiest options is to wire it directly to the rear channels on your factory or aftermarket car stereo. Most of the time, there are factory car speakers in the rear doors, you will need to disconnect these for you to add your 6x9 car speaker to each left and right rear channels. You can add your 6x9 car speakers and keep the rear door speakers playing all off the same rear channels from the back of the headunit, however this will cause the ohm load to each rear channel to be lower than standard. Each 6x9 car speaker will be rated at 4 ohm and so will the factory door speaker, adding them together wiring them side by side will create an 2 ohm load. This will work, but overtime will damage the internal amplifier in the car headunit, as most can't handle an 2 ohm load for long periods of time. Even if it does work, you will get lots of distortion this way. The best method if you're wiring directly from the car headunit is to disconnect the factory rear speakers and use the two remaining channels just for the 6x9 car speakers. This way they will get all the sufficient power the factory or aftermarket headunit can provide from the rear channel of the wiring harness.

If you want the maximum bass and loudness from your car 6x9 speakers, then the best way is to get an separate two channel amplifier. This will allow clean output and provide the 6x9 car speakers to reach there full potential. Adding an car audio amplifier will make the 6x9 car speaker sound quality cleaner and distortion free. This is the proper way to do it, but due to the extra effort of installing an car audio amplifier, people often avoid this. Make sure you match the RMS of each 6x9 car speaker with an aftermarket car audio amplifier you are considering buying. RMS is the true wattage rating per car speaker, the other car speaker max or peak power ratings are just rubbish so you buy the thing. To do it right, you need an two channel stereo amplifier, don't go for an mono amplifier as they are just for bass subwoofers. Also you can add an speaker box for each 6x9 speaker to increase bass response. You can buy an pair of 6x9 car speaker boxes for like £40.00 of ebay or amazon.

How To Fix Crackling Car Speakers or Tweeters

Car audio bass system

 

An usual car audio system consists of an car speaker and an tweeters. Some premium upgraded sound systems may have an additional amplifier under the seat to power an car subwoofer in the trunk. If you have noticed recently that your car speaker or car tweeters is crackling, this guide will help you troubleshoot the car audio problem. But first, you will need to identify were there crackling is coming from, play an song of your choice and open all of the car doors. Examine each car speaker and tweeter fitted into each door and use your ears to find the crackling. Once you have identified the exact speaker or tweeter the crackling sound is coming from, you are now able to look into the issue in more detail. An cracking sound doesn't mean the car audio component is failing, there can be others causes. 

The first cause can be dirt or dust vibrating on the car speaker cone. Car tweeters are very sensitive and made from soft fragile parts. Even if there is an slight bit of dirt on it, it will cause an crackling sound to appear at high volumes placed via the car stereo. I would recommend that you take the driver out of its housing and inspect. Give it an quick clean with an can of compressed air on the top part of the diagraph (speaker cone) and under were you can see the voice coil and spider. Avoid using an kind of cleaning solvents as this can damage the speaker, just an damp cloth will do just fine. Now replace the car speaker or car tweeter back into its original location, has the cracking sound disappeared? 

If the cracking car speakers is still make that annoying noise, then you will need to troubleshoot this car audio problem further. The speaker wire can be the cause to the crackling, it could be damaged from corrosion or worn out. Inspect the spade connectors that insert into the back of the speaker. Are they loose or has an wire come out of it? Also remove the radio from your vehicle and check the connection on the back? Has any of the pins come out of the quadlock connector block? There is often cases were wires have been altered in the past behind the radio and an wire may have come loose. The best way to rule out if the car speaker or car tweeter is blown is by connecting an direct wire onto the positive and negative terminals found on the back of it. Then connect the other end to an working speaker channel of your radio, does the crackling still occur?

If you still hear the cracking, while bypassing the factory wiring in the door, then the car speaker or car tweeters is blown and is damaged. This can happen from age or distortion damaging it. If the cracking has gone, then the factory wiring that runs from the door card through the rubber boot to the back of the radio will need replacing. This can easily be done, the most tricky part is feeding the speaker wire into the small black rubber boot found near the door hinge. The best method is to use an metal coat hanger attach the new speaker to it using some tape and push the pointed part through the opening of the rubber boot to get it through the other end.

How To Fix one side of speakers not working in car

An car audio system from the factory will have an midrange driver and tweeter in each door in the front and coaxial system speakers in the rear. In total, the basic factory car audio system has an total of four car speakers in the entire system. Some upgraded factory car audio systems from companies such as Bose may add an additional small compact subwoofer in the boot to give more of an bass sound. If you have noticed that one side of the speaker is not working in your car, either drivers side speaker not working or passenger side speaker not working, we will help you troubleshoot this car audio problem.

The first thing to check is the fader and balance setting on your factory car stereo. You will need to go into the audio settings found within the menu interface of the car stereo. Sometimes what can happen is you can by accident adjust these settings by pressing the wrong button on the car stereo quickly. The balance should be set to the middle and the same should apply to the fader. This will ensure the audio amplifier chip found within the headunit provides an equal rms power output to each individual speaker. If you still are not getting the full sound from your car audio system, there is an possibility the speaker wire for the not working speaker is degraded overtime. Over the years, opening and closing the door daily can cause either an weak or broken car speaker connection causing no sound. The best way is to remove the door boot push it back if possible and inspect the speaker wires for any damage.

If the car speaker wires look ok physically from the outside, then the wiring is fine. The issue will most likely be an faulty or worn out car speaker that is not working. Factory car speakers don't tend to last as long as aftermarket car speakers due to the cheap material they are constructed from. To replace the car speaker you will need to remove the door card.  To help you, you should be able to find an video tutorial on Youtube by doing an quick search. There will be hidden screws behind plastic pop off handles and covers. Then you will need to use an pry tool to remove the clips around the door, sometimes these can break and can fall off. Next remove any electrical connector for any window switches and also remove the handle release cable on the door. Now, you will have full access to the blown car speaker. Usually it is either an Philips or torx screws that you need to remove to pop the blown speaker off. Sometimes, there will be metal rivets from the factory that you need to drill out and apply fresh screw in. Once you have removed the blown car speaker, attach the speaker terminal onto the new speaker and screw it in place.

How To Make Your Car Tweeters Sound More Louder

 

Car tweeters are usually combined with an midrange driver that is mounted into the lower part of an car door. The tweeter plays the really high frequencies usually in the 20,000 HZ range, that gives music that extra sparkle. If you want to make your car tweeters sound louder, you will need to consider some tweaking to your car audio sound system configuration. The first thing you should consider is purchasing an aftermarket car stereo. This is because it has more tuning facilities, usually an preset car equaliser is found within the menu of the car stereo. This allows you to make adjustments to certain frequency bands, giving you full control of the frequencies that are target for the tweeters to play. In general, the frequencies towards the left hand side are geared towards bass, subwoofer level 80 Hz and below and the ones towards the right lead up the the tweeters. You want to play around with frequencies around the 10,000 HZ to 20,000HZ range. Increase the DB in these eq sliders to make your car tweeters louder. 

Adding an car amplifier to your component speakers, will certainly increase loudness and reduce distortion resulting in the most clear sound. Make sure you match the RMS of the car speaker set you want to amplify with the correct ohms and rms the car amp you intend to use. Overpowering car damage speakers if the gain is not setup correctly on an more powerful car amplifier. If you are powering your car tweeters and car speakers from the stock standard factory radio, they will be getting at most 10 to 15 rms, which in this day and age is not alot. In the car audio world, more power means more output.

An crossover is something that you can fit inline with the car speaker and car tweeter. This is to ensure that both parts of the car audio system play correctly and efficiently. Sometimes crossovers can also have an tweeter boost switch that increase the sound output on them, with an predefined eq setting within the technology of the circuit. Pressing this can make the tweeters sound louder. Adding an crossover can seem extra work but this will ensure your car tweeters are playing sound that they are designed for. Some people like harsh treble, some people like more bass, everybody has different listening tastes.

How To Make Car Speakers More Louder

car speakers make me deaf

 

If you're wanting more volume out of your car audio system, then you are in the right place. Our car audio blog contains many different interesting car audio related articles to help you optimise your car system. Car audio speakers is something we will be looking into today. If you want loud car audio speakers, the two things that you need to look into are the RMS handling power and sensitivity. RMS is the real power rating that is given to car audio speakers. Max or Power rating is mainly marketing and is never an true reflection of how long an car speaker will last. You need to get an car amplifier that matches the exact RMS rating of the car speaker, to get the most out of the driver. Sensitivity is something that is often overlooked, but it is also important. The higher the number, the more efficient the car speakers will play. If you're thinking of running your car speakers just off an bog standard headunit, then this is very important.

Applying sound deadening material onto the doors were your car speakers are installed is something that you should also consider. This will allow you to cover up large gaps found behind the door card. Sealing these up with sheets of sound deadening will provide you with an good sound. Not only will it make your car speakers louder it can also help make your car speakers more bassy. This is because it helps the car door act as an sealed enclosure to an extent to get more sound out of them. Leaky gaps in doors covered by an plastic bag from the factory to stop rain won't provide any dampening effect at all.

Giving your car speaker correct levels of amplification and also applying sound deadening material were relevant can make that big difference. You can also upgrade the car speaker wire to better thicker wire, to help the signal flow better to the speaker. This usually doesn't make it louder, but it can help increase sound quality, as the bigger the copper inside the speaker wire the less electrical resistance.

Another top tip of mine is to ensure that the high pass filter is setup on the car stereo itself or the 4 channel car amplifier you are using to power your car speakers. If you want your car speakers to play louder and become more efficient, then setup the HPF to 100 HZ. This will stop unwanted bass being sent to your car speakers, reducing distortion and also make them play more clear and louder. Adjusting the equaliser setting your aftermarket radio is also something you should consider. Play around with the settings to get the most out your speakers. You will find different frequency bands to increase and decreased this will help you lift up the sound in certain areas. 

How To Get Only Bass From an Car Subwoofer Stop Singing coming out of it

 

In an car audio system, the role of an car subwoofer is to purely focus on playing bass only. The large cone area from an subwoofer being an 10 12 or 15 inch speaker gives it capability to push some deep bass into your trunk. If you notice your car subwoofer is playing bass and also you can hear treble from it, the low pass filter is not switched on or not setup correctly. When this happens, the car subwoofer will not play its best, you will notice an reduction in sound quality and loudness.

There are two types of filters used in car audio for two different instances. The high pass filter is designed for car amplifiers that are powering either your front or rear speakers. People tend to setup the high pass filter to 80HZ to prevent the car speakers in the doors playing bass. This allows your car door speakers to play more clean reducing the amount of distortion created. An low pass filter should be setup to 80 or 60HZ depending your listening tastes. This should only be switched on the bass amplifier that is powering your car subwoofer. This will stop vocals playing out from your car subwoofer, as frequencies below the cut off point are so low to an point treble is muted out.

To only get bass from an car subwoofer and to stop vocals coming out of it, simply switch on the 'LPF' to the on position, this switch will be found on your car amp. Most car amps either that are entry level or high end from big brands such as alpine or pioneer, will have an adjustable crossover switch with that label. There also usually will be an adjustable dial that you can turn using an screwdriver that allows you to set the low pass filter frequency. Ideally, you want to set it at 80 Hz or below. Play an favourite song that has alot of bass and adjust the screw for the low pass filter frequency to how you like your bass to sound. There is no perfect point with this one, as some people prefer louder boomier bass and some car audio listeners like that deep low end rumble like an earthquake.

You also may notice that your aftermarket car headunit will also have an separate low pass filter found within the audio settings on the unit. This is also good to have, however if you have enabled it on the car amplifier you can select this to the off option.This is because having two low pass filters switched on at the same time will impact sound quality and we recommend that you let the do car amplifier the work. The low pass filter only an headunit will only work if switched on and if the RCA cables are connected to the 'SUB OUT' RCA plugs on the back of the car stereo.

How To Prevent Blowing Car Audio Tweeters

Car audio tweeters are the most sensitive component used in car audio to produce high treble frequencies. They don't require a lot of rms power to get going compared to an car subwoofer, as tweeters are efficient in playing the highs, hence why they are so small. Car tweeters in conjunction with an midrange car speaker will provide greater clarity over coaxial style speakers. If you notice you keep blowing car tweeters, chances are you are damaging them by improper settings. Tweeters can handle anything below 2 kHz, if you don't have an crossover in place, all frequencies including low bass will be sent to them. This overtime will damage them and you also can't tell because the tweeter won't play bass, however the small tiny diagraph will try to play low bass notes and simply will fail. The best way to prevent your car tweeters from blowing up is to protect them. You can do this by adding an capacitor onto the positive terminal on the car tweeter. This will filter out any unwanted bass being played to them, this is the cheap way of doing it. 

The proper way to protect your tweeters from bass sounds is to connect an standalone crossover box. There will be one for the left side and one required for the right side. An crossover box has internal filtering components to ensure both the mid range and tweeter is playing the right sounds. This will not only protect your equipment, but it will also increase the amount of sound quality in your car audio system. Connecting an crossover box is simple. There will be one set of terminal labelled as input, you connect either the speaker channel wire from your car headunit or car amplifier. This wire sends music to the crossover to process the music. Then there will be two set of terminals, one to connect the car tweeter to and the set to connect the car speaker to. Make sure when wiring that you do the polarity correctly to ensure best sound.

An crossover usually helps, but also remember not to overpower your car tweeters. Always check the RMS rating of them and try to match it closely as possible to the rms on the car amplifier. Also ensure that your gain your car amplifier is correctly tuned to prevent distortion of clipping. If it sounds distorted simply turn it down.